2011-2025 Ford 6.7L Powerstroke CP4 Disaster Prevention Kit Installation Guide
Source: https://www.spelabautoparts.com/pages/2011-2025-ford-6-7l-powerstroke-cp4-disaster-prevention-kit-installation-guide
You can also download the original PDF of these installation instructions: SPELAB CP4 Bypass/Disaster Prevention Kit Installation Warning Use compressed air to blow out all components prior to installing to prevent debris from contaminating the fuel system. Common rail diesel fuel systems are very sensitive to debris, prioritize cleanliness during install. 1. If you suspect a failed CP4 high pressure fuel pump AFTER the kit has been installed, the quickest way to confirm is to cut open the return fuel filter and inspect the filter media for metal debris. 2. The return side fuel filter recommended change interval is the same as the other fuel filters on the vehicle. See below for the factory Ford filter change recommendations based on duty cycle and operating conditions. Vehicle Service 6.7L Normal 6.7L Special* Fuel Filter Change (both) Change both fuel filters every 3rd oil change or every 22,500 miles (36,000 km) or as indicated by the message center, whichever comes first. Change every 15,000 miles (24,000 km) or 600 engine hours or as indicated by the message center, whichever comes first. *Special = Operating Conditions like Extensive Towing, Long Idle Time, Extended Low Speed Driving. For Off Road/Dusty Conditions oil change intervals should be every 7,500 miles (12,000 km) or 300 hours of engine operation. Installation Procedure **(For 2020+ please see special instructions)** Step 1: Disconnect the positive and negative battery cables from the primary and secondary battery. Step 2: Remove radiator cap to relieve pressure. Remove coolant lines that covering over the top. (Just to get them out of the way) Step 3: Disconnect vacuum line. Step 4: Remove MAF sensor. Remove air intake box. Remove the vacuum line. Step 5: Remove fuel filter. Note: Once you remove the fuel line, place it back on the lower hardline to keep it clean. Take special care to not introduce debris into the filter or fuel line. Step 6: Remove hot side and cold side charge pipe. Step 7: Remove the fuel filter housing. Step 8: Remove the plastic upper intake manifold. Remove all fifteen (15) 8mm bolts. Remove all electrical connections and wires from the intake. Step 9: Remove the EGR tube between the cooler and lower intake. Be sure to keep track of the gaskets as they will be reused. Disconnect the electrical connection and remove the wire clip from bottom of the lower intake. Step 10: Remove crankcase breather. Note: This hose may be very brittle, be cautious to avoid damage. Step 11: Remove the Lower Intake. Step 12: Remove Fuel Control Actuator (FCA). NOTE: Thoroughly clean the area around the FCA with brake cleaner and compressed air before removing the FCA. ENSURE NO DEBRIS ENTERS THE INLET OF THE PUMP WITH THE FCA REMOVED. Step 13: Ensure pump is healthy by checking metering unit for debris. It should match figure 13. If it looks like figure 13a, the pump and fuel system must be replaced. Step 14: Remove dust covers from the bypass hose assembly quick connects and blow out hoses with compressed air while being careful to not damage o-rings inside the quick connect fittings. (The hoses are clean before shipping, but blowing them out again ensures no debris was able to enter the bypass block passages and hose during transport or handling). Step 15: Install the large and small O-ring onto the Bypass Block. Push the o-ring into the groove to retain it. Step 16: Install Bypass Block and FCA onto the CP4 using supplied M5 allen head bolts. Torque to 60 inch-lbs. Step 17: Reinstall the lower intake. Torque bolts to 18 ft-lb. Tighten hose clamps Step 17a: In rare cases on early model years, it may be necessary to remove the casting flash on the lower intake to increase the clearance to the Fuel Control Actuator (FCA) electrical connector on top of the CP4 fuel pump with the Bypass Block installed. Confirm adequate clearance before final intake assembly. Step 18: Reinstall the EGR Tube with gaskets in place. Torque bolts to 89 in-lb. Step 19: Reinstall the upper plastic intake. Torque bolts to 89 in-lb. Install fasteners for dipsticks. Reconnect all electrical connections and reinstall insulation on pressure sensor. Ensure that all wires are routed away from hot exhaust parts as they were previously. Step 20: Reinstall the OEM fuel filter and housing. Step 21: Complete bypass kit installation. Reinstall crankcase breather hose to lower intake (take special care if the hose is brittle). Remove factory fuel line from lower hard line. Push quick connect fittings onto their respective barbs, until you hear an audible click. Give them a small tug to ensure they are seated all the way. Use the supplied zip tie hose clips to keep the hose from chafing on nearby components. Use one on the crank case vent and if needed on the oil filler neck. (Adjust as necessary to ensure hose does not rub on nearby components.) Step 21a: 2017+ model years Step 22: Reinstall charge pipe. 2020+ Special Instructions A: Remove the factory plastic line and quick connect assembly. This is best done by removing the factory supply and return line assembly and using a heat gun to soften the hose enough to pull it off the factory hardline as shown. B: Install the supplied hose and quick connect barb assembly. NOTE: Take special care to not introduce debris into the system. Slide the hose over the barbs on the factory supply tube. Ensure there is no metal to metal contact from the aluminum fitting to the tube inside the hose. Tighten the hose clamp behind the 2nd barb. Install the OEM metal lines and adapter assembly. Continue the install as normal on step 15. Install The Filter Head Assembly Step 23: Install the small o-rings onto the aluminum filter head fittings & hand-thread the fittings into the filter head. Using a 15mm deep-well socket, torque both fittings to 120 in-lb (10 ft-lb). DO NOT OVERTIGHTEN or damage may occur. Step 24: Thread the rubber isolators into the backside of the filter head until hand-tight. Return Hose Installation Filter Flow Diagram Step 25: Place some absorbent towels around the joint to catch diesel fuel. Disconnect the return line quick connect fitting from the factory metal return barb. Hold the factory plastic line and rotate the plastic female quick connect fitting inside the molded tube 180°, so it is facing upward. This may have to be slightly adjusted later. Step 26: Install the hose with a plastic connector on both ends (right side of the filter - "Return Fuel from Engine") The larger quick connect goes on the OEM metal barb that you removed the factory fitting from earlier. The hose wraps around the back of the filter and the plastic quick connect attaches to the right side of the filter head (Return Fuel from Engine). Step 27: Install the supplied zip tie hose clip. Put the zip tie around the factory fuel supply line and clip the hose to it, adjust as necessary to keep the hose off the brake booster and reservoir. Step 28: Install the shorter left side hose (left side of the filter - "Return Fuel to Tank") The aluminum barb goes into the OEM quick connect fitting that was previously disconnected and rotated upward. The other side connects to the left side of the filter head (Return Fuel to Tank). Adjust rotation of quick connect fitting as necessary to avoid chafing. Filter Head Mounting The filter head mounting is slightly different between 2011-2016 and 2017+ model years. Step 29a: 2011-2016: Use short panhead bolt – no washer or spacer Step 29b: 2017+ i. Loosen the cowl to access the hole for installing the fuel filter ii. Remove the plastic fastener from cowl iii. Put the washer on the long bolt. Put the provided long bolt through the hole, then the spacer, then the filter bracket. Tighten the provided nylon lock nut. Step 30: Install fuel filter. Lubricate the filter o-ring with motor oil, diesel fuel, or similar lubricant. Spin-On filter until the rubber seal contacts the filter head and rotate ½ turn until fully tight by hand. Step 31: Purge air and check for leaks. Cycle the key to the accessory position to allow the electric fuel pump to run for 30 seconds to purge air prior to starting the engine. Start the engine and check for leaks. Technical Support Technical Support: email us service@spelabautoparts.com www.spelabautoparts.com Phone: +1 888 301 8666 Mon - Fri: 9:00 AM - 6:00 PM EST Sat - Sun: Closed